![]() ![]()
The computer receives network settings from this interface via DHCP, and then goes through it to the Internet, like through a regular wired LAN. ![]() With HILINK firmware, the modem works in the router mode and is presented to the computer as a network interface (usb-ethernet-rndis). It is possible to prohibit the transformation of songs. Under linux, switching is done by the usb-modeswitch program. HUAWEI E303 FIRMWARE UPDATE SOFTWAREUnder windows, this is done by carrier software available on a virtual CD, or by the huawei proprietary program Mobile Partner. In order for modem ports to appear, you need to switch the composition. The initial USB stick stick composition is a virtual CD-ROM and microSD card reader. At the same time, the computer receives an IP address directly from the cellular provider through a DHCP request, and the modem acts as a network bridge, transmitting the packets from the computer to the cellular network and back without changing them. The main feature of the stick mode is to establish the connection and support the operation of the channel using the OS of the computer to which the modem is connected. In this case, the modem emulates a network interface through which data is transmitted, and only control commands are sent through the AT port. In addition to the PPP mode, there is an NDIS mode. The speed is limited - no more than 20-30 Mbit at the reception. This is how almost all previous-generation 3G modems work. I used this method to flash a “permanently locked” modem with 10 wrong unlock attempts and it worked fine.With this firmware, the device behaves like a classic USB modem: there is a command AT-port through which you can establish a connection using the PPP protocol (RAS). Now you’ve successfully flashed your modem. Also, this should take less than five minutes to complete and after that, you should have a different modem software that’s not branded with your home network logo and customizations. HUAWEI E303 FIRMWARE UPDATE UPGRADEHit the Next button as before and the procedure is very much similar to the firmware upgrade you did earlier.Įasy, isn’t it? It’s more like installing a software on your computer. – Again, the software should search for your device – Unzip the file and run the executable file HUAWEI E303 FIRMWARE UPDATE UPDATEIt’s here you’ll be needing the Dashboard Update file you downloaded. HUAWEI E303 FIRMWARE UPDATE INSTALLI had to install a different dashboard to make me use our network provider settings here in Nigeria. The dashboard wouldn’t let any me use any other SIM though the modem is already unlocked. Installing a different dashboardĮven with an upgraded firmware, I was still seeing that same dashboard that came from 3 network. – Congratulations! You just upgraded you modem firmware successfully! 3. Just wait till you see a message that looks like this: – At this point, you don’t have to do anything. – The process starts and normally, this should take less than 10 minutes. Remember the Flash code you generated earlier? Enter it here. This only happens when the new firmware version is different from the existing one on the device. – When you hit the start button, you may be prompted to enter your Flash code. Do not remove your modem and be sure you have enough poer on your laptop or UPS to last for about 30 minutes. – When the flashing starts, be sure you follow the instruction on-screen. – On the next page, simply hit the Next button – The program searches for your modem for some seconds Now to upgrade the firmware, unzip the firmware update you downloaded and double-click the. – Now, download Firmware Update and Dashboard Update – On the next page, select your model and click the same modem icon again. – Select Huawei or what model your modem is and click the tiny modem icon ![]() You can always check DC-Unlocker , Huawei Firmwares or Modem Unlock website. Update: These sites don’t seem to have the firmwares anymore. You can download it from their official website but I prefer and recommend – First, you must download the right firmware for your modem. – Lastly, click on Calculate to generate the flash code. This should both unlock your modem and reset the counter at the same time – Be sure Auto-Calc Code and Auto-Unlock Modem are both marked Your modem should be automatically detected so far you checked AUTO CONNECTION under connection mode Of course, you can still do it if you want to unlock your modem and anyway. ![]() If you haven’t entered your unlock code 10 times like the guy in question did, you should skip this step. I had to reset the counter with a software first. Like I said earlier, upgrading the firmware did not reset the unlock counter which read 10 out of 10. HUAWEI E303 FIRMWARE UPDATE HOW TOMust Read: How to Unlock Huawei E303 USB Modem ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |